netsh interface ipv6 set privacy state=disabled store=active
netsh interface ipv6 set privacy state=disabled store=persistent
netsh interface ipv6 set global randomizeidentifiers=disabled store=active
netsh interface ipv6 set global randomizeidentifiers=disabled store=persistent
Restart windows
sh interface snmp-ifindex
-------------------------------------------------------------------------------- Port IFMIB Ifindex (hex) -------------------------------------------------------------------------------- Eth1/1 436207616 (0x1a000000) Eth1/2 436211712 (0x1a001000) Eth1/3 436215808 (0x1a002000) Eth1/4 436219904 (0x1a003000) Eth1/5 436224000 (0x1a004000) .. Po10 369098761 (0x16000009) .. Eth100/1/1 526581760 (0x1f630000)
Before configure your device over SNMP, you need to enable read-write and limit the access with an ACL.
snmp-server community <your_community> RW <Access-list>
Now you can configured your device with snmp-set command. The following example show how upload a new configuration on your running-config with a TFTP Server.
snmpset -v <version> -c <community> <your_router> \ .1.3.6.1.4.1.9.9.96.1.1.1.1.3.50 i 1 \ .1.3.6.1.4.1.9.9.96.1.1.1.1.4.50 i 4 \ .1.3.6.1.4.1.9.9.96.1.1.1.1.5.50 a "<IP TFTP Server>" \ .1.3.6.1.4.1.9.9.96.1.1.1.1.6.50 s "<filename>" \ .1.3.6.1.4.1.9.9.96.1.1.1.1.14.50 i 4
You also can use FTP, SCP, … You have more information about the mib here.
1- Create a VSAN
vsan database vsan 10 name SAN-TEST
2- Asign interfaces to VSAN
vsan 10 interface fc1/8
3- Create aliases
fcalias name SAN1_SPA_0 vsan 10 member pwwn 50:00:00:00:00:00:00:00 fcalias name SRV1_HBA01 vsan 10 member pwwn 21:00:00:00:00:00:00:00
4- Create Zone with aliases
zone name Z_SAN1_SPA_0_SRV1_HBA01 vsan 10 member fcalias SAN1_SPA_0 member fcalias SRV1_HBA01
5- Asign Zone to ZoneSet
zoneset name ZONESET_VSAN10 vsan 10 member Z_SAN1_SPA_0_SRV1_HBA01
6- Apply and activate ZoneSet
zoneset activate name ZONESET_VSAN10 vsan 10
Troubleshooting
Example to view WWN and PWWN on MDS:
# sh flogi database -------------------------------------------------------------------------------- INTERFACE VSAN FCID PORT NAME NODE NAME -------------------------------------------------------------------------------- fc1/1 10 0x250000 50:06:01:61:08:xx:xx:xx 50:06:01:60:88:xx:xx:xx fc1/2 10 0x250100 50:06:01:69:08:xx:xx:xx 50:06:01:60:88:xx:xx:xx fc1/3 10 0x250400 21:00:00:24:ff:xx:xx:xx 20:00:00:24:ff:xx:xx:xx fc1/4 10 0x250300 21:00:00:24:ff:xx:xx:xx 20:00:00:24:ff:xx:xx:xx
This example displays how view logs of the mgmt0-access ACL:
# sh ip access-lists
IP access list mgmt0-access statistics per-entry 10 permit tcp addrgroup NOC addrgroup RouterBlock eq 22 [match=2611] 20 permit udp addrgroup NOC addrgroup RouterBlock eq snmp [match=0] 40 permit udp addrgroup NOC eq ntp addrgroup RouterBlock [match=0] 50 permit tcp addrgroup NOC eq tacacs addrgroup RouterBlock [match=2055]
60 permit tcp addrgroup NOC addrgroup RouterBlock eq www [match=0] 500 permit ip addrgroup NOC addrgroup RouterBlock log [match=818]
To view the log, you need to use the following command :
# sh log ip access-list cache Src IP Dst IP S-Port D-Port Src Intf Protocol Hits -------------------------------------------------------------------------------- ---------------- 10.200.0.20 10.200.0.11 40196 161 mgmt0 (6)TCP 65 10.200.0.20 10.200.0.11 56267 80 mgmt0 (6)TCP 0
Number of cache entries: 2 --------------------------------------------------------------------------------