{"id":254,"date":"2016-07-23T16:32:00","date_gmt":"2016-07-23T15:32:00","guid":{"rendered":"https:\/\/zed-network.fr\/?p=254"},"modified":"2020-08-24T19:43:32","modified_gmt":"2020-08-24T18:43:32","slug":"convert-lwapp-to-autonomous-ap","status":"publish","type":"post","link":"https:\/\/zed-network.fr\/?p=254","title":{"rendered":"How to Convert Cisco LWAPP to Autonomous AP"},"content":{"rendered":"\n<p class=\"wp-block-paragraph\">To use console port on Access Point, you need a real serial port on your compute. Usually USB to Serial convert doesn&#8217;t work.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Default password :<\/p>\n\n\n<pre><code>AP4403.xxxx.xxxx&gt;en<\/code><\/pre>\n<p>Password: &lt;= Cisco<\/p>\n<pre>AP4403.xxxx.xxxx#sh ver<br \/><br \/>Cisco IOS Software, C2600 Software (AP3G2-RCVK9W8-M), Version 15.2(2)JA, RELEASE SOFTWARE (fc1)Technical Support: http:\/\/www.cisco.com\/techsupportCopyright (c) 1986-2012 by Cisco Systems, Inc.Compiled Thu 23-Aug-12 02:43 by prod_rel_team<br \/>ROM: Bootstrap program is C2600 boot loaderBOOTLDR: C2600 Boot Loader (AP3G2-BOOT-M)<br \/>LoaderVersion 12.4(25e)JA1, RELEASE SOFTWARE (fc1)<br \/>AP4403.a7a0.db3e uptime is 4 minutesSystem returned to ROM by power-onSystem image file is \"flash:\/ap3g2-rcvk9w8-mx\/ap3g2-rcvk9w8-xx\"<\/pre>\n<p>Enable configuration terminal to setup and IP address and download the new code.<\/p>\n<pre>P4403.xxxx.xxxx#debug capwap console cli<br \/>This command is meant only for debugging\/troubleshooting<br \/>Any configuration change may result in different<br \/>behavior from centralized configuration.<br \/><br \/>CAPWAP console CLI allow\/disallow debugging is on<br \/>AP4403.a7a0.db3e#<br \/>AP4403.a7a0.db3e(config)#ip default-gateway 10.0.100.254<br \/>AP4403.a7a0.db3e(config-if)#int gi0<br \/>AP4403.a7a0.db3e(config-if)#ip address 10.0.100.200 255.255.255.0<br \/>AP4403.a7a0.db3e(config-if)#no sh<br \/>AP4403.a7a0.db3e(config-if)#exit<br \/>AP4403.a7a0.db3e(config)#end<br \/>AP4403.a7a0.db3e#ping<br \/>Type escape sequence to abort.<br \/>Sending 5, 100-byte ICMP Echos to 10.0.100.1, timeout is 2 seconds:<br \/>!!!!!<br \/>Success rate is 100 percent (5\/5), round-trip min\/avg\/max = 1\/1\/1 ms<br \/><br \/>AP4403.a7a0.db3e#<strong>archive download-sw \/force-reload \/overwrite tftp:\/\/10.0.100.1\/ap3g2-k9w7-tar.default<\/strong><br \/>examining image...<br \/>Loading ap3g2-k9w7-tar.default from 10.0.100.1 (via BVI1): !<br \/>extracting info (279 bytes)<br \/>Image info:<br \/>Version Suffix: k9w7-.153-3.JC<br \/>Image Name: ap3g2-k9w7-mx.153-3.JC<br \/>Version Directory: ap3g2-k9w7-mx.153-3.JC<br \/>Ios Image Size: 10322432<br \/>Total Image Size: 13384192<br \/>Image Feature: WIRELESS LAN<br \/>Image Family: AP3G2<br \/>Wireless Switch Management Version: 8.2.100.0<br \/>Extracting files...<br \/>ap3g2-k9w7-mx.153-3.JC\/ (directory) 0 (bytes)<br \/>extracting ap3g2-k9w7-mx.153-3.JC\/ap3g2-k9w7-mx.153-3.JC (215867 bytes)<br \/>extracting ap3g2-k9w7-mx.153-3.JC\/ap3g2-k9w7-tx.153-3.JC (73 bytes)<br \/>extracting ap3g2-k9w7-mx.153-3.JC\/ap3g2-bl-2600 (190140 bytes)!<br \/>extracting ap3g2-k9w7-mx.153-3.JC\/ap3g2-bl-3600 (189183 bytes)!<br \/>ap3g2-k9w7-mx.153-3.JC\/html\/ (directory) 0 (bytes)<br \/>ap3g2-k9w7-mx.153-3.JC\/html\/level\/ (directory) 0 (bytes)<br \/>ap3g2-k9w7-mx.153-3.JC\/html\/level\/1\/ (directory) 0 (bytes)<br \/><br \/>extracting ap3g2-k9w7-mx.153-3.JC\/html\/level\/1\/appsui.js (563 bytes)<br \/>extracting ap3g2-k9w7-mx.153-3.JC\/html\/level\/1\/back.shtml (512 bytes)<br \/>extracting ap3g2-k9w7-mx.153-3.JC\/html\/level\/1\/cookies.js (5032 bytes)<br \/>extracting ap3g2-k9w7-mx.153-3.JC\/html\/level\/1\/forms.js (20442 bytes)<br \/>extracting ap3g2-k9w7-mx.153-3.JC\/HA5.bin (2049 bytes)<br \/>extracting ap3g2-k9w7-mx.153-3.JC\/B2.bin (10512 bytes)<br \/>extracting ap3g2-k9w7-mx.153-3.JC\/B5.bin (1995 bytes)<br \/>extracting ap3g2-k9w7-mx.153-3.JC\/Y2.bin (7008 bytes)<br \/>extracting ap3g2-k9w7-mx.153-3.JC\/Y5.bin (1555 bytes)<br \/>extracting ap3g2-k9w7-mx.153-3.JC\/8006.img (568619 bytes)!!!<br \/>extracting ap3g2-k9w7-mx.153-3.JC\/triggerfish.jed (0 bytes)<br \/>extracting ap3g2-k9w7-mx.153-3.JC\/uart_firmware_upgrade.bin (18239 bytes)<br \/>extracting ap3g2-k9w7-mx.153-3.JC\/MCU.bin (8799 bytes)<br \/>extracting ap3g2-k9w7-mx.153-3.JC\/info (279 bytes)<br \/>extracting ap3g2-k9w7-mx.153-3.JC\/file_hashes (36832 bytes)<br \/>extracting ap3g2-k9w7-mx.153-3.JC\/final_hash (141 bytes)<br \/>extracting ap3g2-k9w7-mx.153-3.JC\/final_hash.sig (513 bytes)<br \/>extracting ap3g2-k9w7-mx.153-3.JC\/img_sign_rel.cert (1375 bytes)<br \/>extracting ap3g2-k9w7-mx.153-3.JC\/img_sign_rel_sha2.cert (1371 bytes)<br \/>extracting info.ver (279 bytes)<br \/>[OK - 13434880 bytes]<br \/><br \/>Deleting current version: flash:\/ap3g2-rcvk9w8-mx...done.<br \/>New software image installed in flash:\/ap3g2-k9w7-mx.153-3.JC<br \/>Confi<br \/>Writing out the event log to flash:\/event.log ...<br \/>guring system to use new image...done.<br \/>Requested system reload in progress...<br \/>archive download: takes 220 seconds<br \/><br \/>Write of event.log done<br \/><br \/>*Mar 1 00:13:17.647: %SYS-5-RELOAD: Reload requested by Exec. Reload Reason: Reason unspecified.<br \/>*Mar 1 00:13:17.647: %LWAPP-5-CHANGED: CAPWAP changed state to DOWN<br \/>IOS Bootloader - Starting system.<br \/>flash is writable<br \/>FLASH CHIP: Numonyx Mirrorbit (0089)<br \/>Xmodem file system is available.<br \/>flashfs[0]: 237 files, 8 directories<br \/>flashfs[0]: 0 orphaned files, 0 orphaned directories<br \/>flashfs[0]: Total bytes: 31997952<br \/>flashfs[0]: Bytes used: 13329408<br \/>flashfs[0]: Bytes available: 18668544<br \/>flashfs[0]: flashfs fsck took 16 seconds.<br \/>Reading cookie from SEEPROM<br \/>Base Ethernet MAC address: 44:03:a7:a0:db:3e<br \/>Ethernet speed is 1000 Mb - FULL Duplex<br \/>Loading \"flash:\/ap3g2-k9w7-mx.153-3.JC\/ap3g2-k9w7-mx.153-3.JC\"...#########################<br \/><br \/>File \"flash:\/ap3g2-k9w7-mx.153-3.JC\/ap3g2-k9w7-mx.153-3.JC\" uncompressed and installed, entry point: 0x2003000<br \/>executing...<br \/><br \/>Secondary Bootloader - Starting system.<br \/>Tide MB - 32MB of flash<br \/>Xmodem file system is available.<br \/>flashfs[0]: 237 files, 8 directories<br \/>flashfs[0]: 0 orphaned files, 0 orphaned directories<br \/>flashfs[0]: Total bytes: 31997952<br \/>flashfs[0]: Bytes used: 13329408<br \/>flashfs[0]: Bytes available: 18668544<br \/>flashfs[0]: flashfs fsck took 8 seconds.<br \/>flashfs[1]: 0 files, 1 directories<br \/>flashfs[1]: 0 orphaned files, 0 orphaned directories<br \/>flashfs[1]: Total bytes: 12257280<br \/>flashfs[1]: Bytes used: 1024<br \/>flashfs[1]: Bytes available: 12256256<br \/>flashfs[1]: flashfs fsck took 1 seconds.<br \/>Base Ethernet MAC address: 44:03:a7:a0:db:3e<br \/><br \/>From TFTP Server :<br \/>May 5 19:53:52 srv1 in.tftpd[5529]: connect from 10.0.100.249 (10.0.100.249)<br \/>May 5 19:53:52 srv1 atftpd[5529]: Advanced Trivial FTP server started (0.7)<br \/>May 5 19:53:52 srv1 atftpd[5529]: Serving ap3g2-k9w7-tar.default to 10.0.100.249:50607<br \/>May 5 19:53:52 srv1 atftpd[5529]: Serving ap3g2-k9w7-tar.default to 10.0.100.249:55118<br \/>May 5 19:54:11 srv1 atftpd[5529]: timeout: retrying...<br \/>May 5 19:55:08 srv1 atftpd[5529]: timeout: retrying...<br \/><br \/><br \/><\/pre>","protected":false},"excerpt":{"rendered":"<p>To use console port on Access Point, you need a real serial port on your compute. Usually USB to Serial convert doesn&#8217;t work. Default password : AP4403.xxxx.xxxx&gt;en Password: &lt;= Cisco AP4403.xxxx.xxxx#sh verCisco IOS Software, C2600 Software (AP3G2-RCVK9W8-M), Version 15.2(2)JA, RELEASE SOFTWARE (fc1)Technical Support: http:\/\/www.cisco.com\/techsupportCopyright (c) 1986-2012 by Cisco Systems, Inc.Compiled Thu 23-Aug-12 02:43 by prod_rel_teamROM: [&hellip;]<\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_exactmetrics_skip_tracking":false,"footnotes":""},"categories":[1],"tags":[],"class_list":["post-254","post","type-post","status-publish","format-standard","hentry","category-non-classe"],"_links":{"self":[{"href":"https:\/\/zed-network.fr\/index.php?rest_route=\/wp\/v2\/posts\/254","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/zed-network.fr\/index.php?rest_route=\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/zed-network.fr\/index.php?rest_route=\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/zed-network.fr\/index.php?rest_route=\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/zed-network.fr\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=254"}],"version-history":[{"count":3,"href":"https:\/\/zed-network.fr\/index.php?rest_route=\/wp\/v2\/posts\/254\/revisions"}],"predecessor-version":[{"id":561,"href":"https:\/\/zed-network.fr\/index.php?rest_route=\/wp\/v2\/posts\/254\/revisions\/561"}],"wp:attachment":[{"href":"https:\/\/zed-network.fr\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=254"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/zed-network.fr\/index.php?rest_route=%2Fwp%2Fv2%2Fcategories&post=254"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/zed-network.fr\/index.php?rest_route=%2Fwp%2Fv2%2Ftags&post=254"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}